Description
EASYSeal Multi-surface Water Seal+ – 5 Litres
Overview
Increases the thermal qualities of your home.
EASYSeal Water Seal Plus is a high performance water repellent for all porous building materials. The product can be applied to already damp surfaces which will then, over time dry out, as the coating allows water to escape out and not penetrate in. EASYSeal Water Seal Plus uses technology which is proven to increase Thermal Efficiency, so reducing heating costs.
In addition to acting as a water-proofer, it provides a hard wearing, invisible, protective seal against oil, stains, efflorescence, etc on both horizontal and vertical surfaces with no long-term alteration of the colour of the substrate.
EASYSeal Water Seal Plus is recommended for the treatment of, walls, fountains, monuments, garden stones and paving, headstones, timber structures, fences and decks.
Features include:
- Penetrating water repellent for porous brickwork, masonry and timber
- Provides protective seal against water, oil and staining
- Allows masonry to breathe so moisture escapes
- For use on vertical and horizontal surfaces
- Invisible coating – no long term textural or colour change
EASY Seal Range Comparison Chart
Coverage
Up to 25m²
Note
Coverage will vary with levels of porosity
Features and Benefits
- Penetrating water repellent for porous brickwork, masonry and timber
- Provides protective seal against water, oil and staining
- Allows masonry to breathe so moisture escapes
- For use on vertical and horizontal surfaces
- Invisible coating – no long term textural or colour change
- Proven increased thermal efficiency, reduced heating costs
Brief usage instructions
Application: Use neat as supplied
- Shake container before use
- Always test a small area before use to ensure compatibility and that the finished result is acceptable
- Surface should be clean. Remove loose dirt, moss and other debris from the surface to be treated
- Do not apply in wet or when rain is imminent
- Surfaces can be dry or damp but not wet
- Ideal operating temperature between 10℃ and 30℃. Do not apply during rain, frost or when surface and air temperature is below 5ºC
- Keep pets away until surface is fully dry
- Clean tools and other equipment with warm soapy water
- Do not pour directly onto the surface. The preferred application method is with a low pressure sprayer, but it can be applied with a brush or long haired roller. Apply an even coat and avoid runs and puddles
- For porous surfaces, apply 2 coats. Apply the second coat whilst the surface remains damp from the first coat. Timing depends on temperatures. Allow the product to cure overnight. Optimum performance is reached after 2-3 days, longer in cold, damp conditions
EASYSeal Water seal+ Useage Download
EASYSeal Water Seal+ Safety Sheet
FAQs
You have eight products in your range, what makes them different?
We have a sealer comparison chart that explains at a glance what the main features of each sealer does. Each sealer has been designed to make the job of sealing easier, quicker or both.
I would like to seal my blocked paved driveway, what is the best product for this?
Ideally you should buy BCS (Block and contract), it contains a sand binder and will water proof the whole area, it is also very hard wearing. You could also consider Contract which does a similar job but in a different way, it is cheaper than BCS but will not wear as well, BCS also contains more sand binder than contract.
Have you got a sealer that will still allow the stone to breathe and won’t leave a shiny, or enhanced surface?
Yes, there is a choice of sealers. Our basic sealer is SSP, it’s very good and the most popular sealer in our range. Then there is EASYSeal Ultimate, it contains an added formula ‘Dirt Defence’ which gives the seal an added strength, that makes it harder wearing, it is also water based.
I am about to get my patio cleaned but it is looking dull, I understand you have a sealer that enhances the stone is that right?
Yes, we have two excellent colour enhancers that also seal your paving, these are suitable for most types of natural stone and have been specifically designed to treat and protect Slate, limestone and sandstone. EASYSeal Sandstone Sealer Enhancer and EASYSeal Slate & Limestone Sealer Enhancer – both are designed to impregnate the surface bringing out the natural colour and patterns in the natural stone. By incorporating the sealing and enhancing process, in one application, we have made your job easier and quicker. Unlike most other sealers, our EASYSealers can be used before jointing paving, because they are water based sealers and allow natural stone to breathe thus allowing salts and efflorescence to pass freely through the natural stone paving and wash away from the surface. Beware other sealers that can’t be applied for up to six months and can trap the salts under the surface of the sealer, leaving a horrible milky finish!
I have an exposed wall that takes an age to dry out after it rains, will your sealers work on it?
The product you need is Water Seal Plus, it contains a formula that will not only seal the brickwork preventing further penetration it actually allows trapped water within the bricks to exit. As a result it may actually increase the thermal properties of your home.
I am about to lay a new patio down, when should I seal the paving?
Where ever possible seal the paving before you joint it, the advantages are two fold, not only will you be able to seal the top and sides of the stone, giving it better protection, you will also note that it is not recommended that the paving is sealed for 4 weeks after using EASYjoint. For particularly sensitive stone such as Granite, Black Limestone & Modak we recommend all six sides of the stone are sealed. It is possible for contaminants to be drawn from the sub base into the stone and to the surface.
I have a patio that was sealed several years ago and it looks like there are trapped deposits between the stone surface and sealer. What can I do?
The old sealer that was used can’t have allowed the stone to ‘breathe’ and has trapped salt deposits under the surface of the sealer. Often salts are released from natural stone, normally within 6 months of laying new stone. Firstly you will need to remove the old sealer, you can do this with EASYCare sealer remover to expose the natural stone, it can then be cleaned and re-sealed using a sealer from the EASYSeal range: EASYSeal SSP, Ultimate, Enhancer or Slate & Lime Sealer Enhancer all allow stone to breathe and will not trap salt deposits – thus avoiding those unsightly white stains. If the efflorescence is difficult to remove use EASY Efflorescence Destroyer before sealing it.
Note: Not all white deposits are Efflorescence, for hard calcium deposits you will need to use EASY Mortar Stain and Calcium Remover .
For any further information please do contact us via email or our helpline, also the online chat.
Reviews
There are no reviews yet.